With new generation of the whirpools CS® we step clearly forward. We are continuously creating new multifunction elements which make spa operation easier and which design can please even the most demanding clients.
QUALITY WHIRPOOL
Access to technologies from all sides in order to ensure quick service and repair of any problem or damage. All components and all whirpool seams are clearly visible. Easy repair directly in place and in the most situations without water drainage.
LOW QUALITY WHIRPOOL
Quite often there are 2 or 3 levels of PUR foam and therefore access to technologies is impossible, so whirpool cannot be repaired well directly in place. Possible water leakage can only be solved in a complicated way, whether caused by technology failure or damage caused by a user.
QUALITY WHIRPOOL CONTAINS
Complete insulation of sheathing including entire bottom of the spa. Sufficient insulation requested for central Europe climate it is recommended to be 3 to 4 cm thick and in case of operation during winter months up to 5 to 6 cm. Quality insulation also provides good soundproof features.
LOW QUALITY WHIRPOOL
There is no insulation which results in extremely high expenses on spa operation. The most heating discharge happens in spa corners and around acryl where the area beneath the spa is insufficiently insulated.
QUALITY WHIRPOOL CONTAINS
All engines shall be positioned on silent blocks which prevent any vibration transfer, also applicable to the highest quality engine of prestigious brands due to: quiet operation, long lifetime.... Quality whirpools are positioned on stainless steel and galvanized frames. We cannot recommend PVC, or wooden construction frames – we resolutely refuse wooden frame. Reasons are obvious.
LOW QUALITY WHIRPOOL
Engine output doesn’t comply with amount of water flow. Engines are noisy and resonate significantly due to missing silent blocks, furthermore carry vibration.
QUALITY WHIRPOOL CONTAINS
Width of 22 mm. Sheathing is made from materials which are thermal resistant to deformation and loss of colour shades due to UV radiation. Good thermo-insulation features are matter of course.
LOW QUALITY WHIRPOOL
Width starts at 0,8 mm. Tub sheathing contains simple and light plastic material which shouldn’t be revealed to wind and UV radiation for a long time. Or such sheathing is made only from wooden boards which require instant impregnation.
QUALITY WHIRPOOL CONTAINS
The latest technologies contain ozone cleaning and UV lamp, possibly automats which measure pH values and level of non-chlorine disinfection in the water.
NOT RECOMMENDED
Disinfection In Clear Technologies on brome basis when, if incorrectly applied, the lifetime of spa technologies is eliminated. It is also not recommended chlorine use which effect is eliminated when temperature exceeds 33°C and dosing must be increased many times! High content of chlorine is also a part of technologies using salt on basis of electrolysis when chlorine effect again eliminates lifetime and functionality of single technologies.
QUALITY WHIRPOOL CONTAINS
Energy-saving single circulation pumps operating around 50 to 150 Watts. 80-90% of residual heat from the engine can be transferred to the water. Quality pumps can eliminate engine damage in case of air intake.
UNADVISABLE PUMPS
If there is two-speed massage pump which is multi-functioning and if one speed fails, the entire pump must be replaced. Such pump exchange might be quite pricey, even up to ten thousands crowns. Output of such pump is around 400 watts which results in higher expenses on spa operation.
QUALITY WHIRPOOL CONTAINS
Sufficient insulation of sheating requested for the central European climate is recommended to be 3-4 cm thick and in case of operating during the winter months up to 5-6 cm. Quality insulation also provides good soundproof features. This way of insulation stores accumulated heat in the whirpool and manages to return it back into the spa. This effect operates on the basis of thermal locker.
LOW QUALITY WHIRPOOL
There is no insulation, possibly reflexive insulation (see picture) which is absolutely insufficient and it is only suitable for the southern countries with climatic conditions of temperature around 20°C. In case of outdoor usage in the central Europe operating expenses, regarding spa heating, might be even 10 times higher.
All over the world it appears to be the unique thermal isolating system of shells. This unique element is made of a specially hardened open profile which lowers the cost by up to 50-60%. Due to its composite mixture of elements it is completely resistant to UV radiation and temperatures up to 90°Celsia. As the only producer in the world we guarantee warranty 120 months on our products´ shell.
We would like to introduce the future represented by simplicity linked with elegant luxury.
We will be happy to provide you with more information about this model. Just leave your contact details and we will get back to you.